Thunderbolt designs, builds and load-tests battery packs for industrial drones, UAVs, ground robots and AGVs in our Dubai workshop: high-drain Li-ion packs where every gram counts in the air, LiFePO₄ traction packs where a robot has to work all shift, and replacement packs for machines whose original batteries are worn out or no longer made. Each pack is built to your voltage, current and space, and delivered across the UAE, Saudi Arabia, Qatar, Kuwait, Bahrain and Oman.
What our drone and robot battery service includes
A drone or a robot is only as good as the battery that powers it: it sets the flight time or the working shift, the peak power the motors can draw and how the machine behaves in the heat. We do not resell boxed batteries — we engineer a pack for your machine and hand it over tested. You get:
- Engineering. Sizing from your motors, controller and duty cycle: series and parallel layout, cell choice, BMS current limits, connectors and the enclosure, with a costed proposal.
- The pack. New cells from established manufacturers — high-drain cylindrical Li-ion for aircraft, grade-A prismatic LiFePO₄ for ground robots — matched before assembly, spot-welded or bolted, in holders rather than glue.
- A BMS that fits the machine. Protection for every cell, temperature sensors, balancing, and — where the controller can use it — data over CAN, RS485 or UART, or a Bluetooth app for the operator.
- A load test and its log. Every pack is charged, balanced and discharged at its working current on our benches before it leaves, so you get its real capacity and how it behaved under load.
- Repacks and replacements. New cells in a worn pack's housing, or a new pack to the original dimensions and connector, for industrial drones, robots and AGVs.
- Delivery, warranty and service. Pickup in Dubai or delivery across the UAE and the GCC under our delivery policy; warranty up to 36 months on components and workmanship, stated in the order.
Who it is for
| Customer | What they need | Typical pack |
|---|---|---|
| Industrial and cargo drone operators | More flight time or payload, packs that survive summer, spares that match | Li-ion 6S–14S (22–52 V), 10–40 Ah, high-drain cells |
| UAV and robotics developers | Prototype packs to a drawing, then the same pack in a small series | Li-ion or LiFePO₄, 12–72 V, built to the CAD envelope |
| Ground robots and tracked platforms | A traction pack that runs a full shift and talks to the controller | LiFePO₄ 24–48 V, 50–150 Ah, CAN/RS485 |
| AGV and AMR fleets, warehouses | Lithium instead of lead-acid, opportunity charging, no watering | LiFePO₄ 24–48 V, 50–200 Ah |
| Universities, labs and competition teams | One-off packs to an unusual shape, voltage or current | Any chemistry, 3.6–96 V |
Why a custom battery for a drone or robot
- The original pack is not sold here, or no longer made. Many industrial machines are imported with a handful of batteries. When they wear out, a pack built to the same dimensions and connector keeps the machine flying or driving.
- More flight time or a longer shift. Newer high-capacity cells often fit more ampere-hours into the same space as the original pack.
- Peak current without sagging. Take-off, climbing, a robot on a ramp or a loaded track draws several times its average current. A pack built around that peak keeps its voltage up and does not trip.
- Heat. A pack designed for a European lab can age quickly on a Gulf site. Cell choice, spacing, holders and BMS temperature limits are set for where the machine really works.
- Data. A smart BMS can report each cell's voltage, the temperature and the state of charge to the controller or the operator's phone, instead of a single voltage reading.
How it works: from brief to a tested pack
- Brief. You send the machine, the motor or controller data, the current pack's label and dimensions, and what you want to change — by WhatsApp or the quote form.
- Engineering and proposal. The configuration, the cells and their datasheet, the BMS and connectors, the weight estimate, the warranty, the price and the date.
- Assembly. Cell matching, welding or bolting, BMS programming and the enclosure, in our Dubai workshop.
- Capacity and load test. Each pack is charged, balanced and discharged at its working current; you receive the measured capacity and the test log.
- Delivery or pickup. Builds start from two working days; larger or more complex packs take longer, and the date is in the quote.
- Support. Questions are answered from the BMS data; capacity tests, cell replacement and repacks when the pack ages.
Why Thunderbolt
- Built and tested in Dubai. The pack is designed for your machine and serviced locally, not shipped back to a factory.
- From one prototype to a series. We build single packs to a drawing and then repeat them identically.
- Aircraft and ground machines. We build light high-drain packs for flight and heavy traction packs for robots — and Thunderbolt is certified to supply batteries to the aviation industry.
- Proof before delivery. Over 1,200 packs shipped, every one load-tested before it left the bench.
Drone battery and robot battery packs we build
Every build starts from the machine: its voltage, its peak and continuous current, the space for the pack and how long it has to run. The ranges we quote most often:
| Machine | Voltage | Capacity | Chemistry |
|---|---|---|---|
| Small multirotor, mapping drone | 6S, 22.2 V | 5–20 Ah | Li-ion high-drain or LiPo |
| Heavy-lift, cargo or spraying drone | 12S–14S, 44–52 V | 16–40 Ah | Li-ion high-drain |
| Fixed-wing or VTOL UAV | 6S–12S | 10–30 Ah | Li-ion high-energy |
| Small ground robot, inspection crawler | 12–24 V | 10–50 Ah | Li-ion or LiFePO₄ |
| Tracked platform, outdoor robot | 48 V | 50–150 Ah | LiFePO₄ |
| AGV, AMR, tugger | 24–48 V | 50–200 Ah | LiFePO₄ |
These are typical builds, not limits: we build from 3.6 to 96 V, and an unusual voltage, a narrow battery bay or a pack split into two halves for balance is exactly what a custom build is for.
Looking for a DJI battery?
We do not sell DJI batteries, and we do not rebuild the smart batteries of consumer camera drones: they are designed for one model and its firmware, and for those drones the right answer is a genuine battery from an authorised dealer. What we do is different. Industrial, agricultural, cargo and custom-frame drones often run on standard Li-ion packs with a plain power connector, and those we can build new, repack with fresh cells, or redesign for more capacity; a LiPo-powered frame can often move to a high-drain Li-ion pack with longer life. If you are not sure which kind your drone uses, send us a photo of the battery label and the connector.
LiPo, Li-ion or LiFePO₄: choosing a drone or robot battery
The chemistry follows the job. In the air, every gram costs flight time; on the ground, cycle life and safety in heat matter more than weight.
| Chemistry | Strength | Weakness | Where it fits |
|---|---|---|---|
| LiPo (lithium-polymer pouch) | Very high burst current, light | Shorter cycle life, swells when abused or stored full and hot | Racing and FPV drones, short high-power flights |
| Li-ion cylindrical (NMC/NCA, 18650 and 21700) | Highest energy per kilogram, robust steel cans | Lower burst current than LiPo for the same weight | Long-endurance and cargo drones, light robots |
| LiFePO₄ | Thousands of cycles, among the most thermally stable lithium options | Heavier for the same energy | Ground robots, AGVs, tracked platforms |
| LTO | Very fast charge, very long life | Heaviest, lowest energy density | Robots that charge many times a shift |
For most industrial drones we now recommend high-drain 21700 Li-ion cells: they carry more energy than LiPo for the same weight and age more slowly, and the current they deliver is enough for steady flight when the pack has enough cells in parallel. For ground robots, LiFePO₄ is our default.
3S, 6S, 12S: what the numbers on a LiPo battery mean
"S" is the number of cells in series, "P" the number in parallel. A LiPo cell is 3.7 V nominal (3.6 V for most cylindrical Li-ion cells) and 4.2 V full, so:
6S = 22.2 V nominal, 25.2 V full
12S = 44.4 V nominal, 50.4 V full
energy = voltage × capacity: 6S 10 Ah = 22.2 V × 10 Ah = 222 Wh
The "C" rating on a LiPo label is the maximum discharge current as a multiple of capacity: a 5 Ah pack at 20C is rated for 100 A. On a custom pack we state the continuous and peak current in amperes instead, set them as limits in the BMS and prove them on the test bench. A 3S LiPo battery charger must balance-charge each cell to 4.2 V; for our packs we specify the charger together with the pack.
Drone and robot batteries in Gulf heat and dust
Lithium cells perform well when warm but age faster when they are kept hot. Battery University gives a charging range of 0–45 °C for Li-ion and notes that heat shortens life (BU-410); stored for a year at 40 °C fully charged, a Li-ion cell keeps an estimated 65% of its capacity, against 85% when stored at 40% charge (BU-808). What we do about it:
- Holders, not glue. Cells sit in plastic holders with gaps between them, so heat spreads and the pack can be serviced.
- Temperature sensors in the right places. Several sensors on the cells, so the BMS limits charging and discharging before the cells are at risk.
- Current with a margin. We size the parallel groups so the pack works below the cells' limit in summer, not at it.
- Dust and sand. Sealed connectors, closed enclosures and coated contacts for robots that work outdoors; shade and charging indoors for drones between flights.
- Storage charge. Packs kept between missions should sit at about 40–60% charge in a cool room, not full in a vehicle.
Inside a custom drone or robot battery pack
- Cells. New cells from manufacturers such as EVE, Samsung and LG, checked for voltage and internal resistance and matched before assembly. High-drain cylindrical cells for aircraft; grade-A prismatic LiFePO₄ for traction.
- Holders and frame. Plastic holders for cylindrical cells, compression holders for prismatic cells — holders keep the pack rigid under vibration, and with no glue it can be opened later.
- Welds and busbars. Nickel strip spot-welded in layers sized for the current, or copper busbars with torque-marked bolts for large packs.
- BMS. Over- and under-voltage, over-current, short-circuit and temperature protection for every cell; a current limit set in software to the machine's real peak; active balancing on large traction packs.
- Communication. CAN or RS485 for robot controllers, UART or a Bluetooth app where the operator needs to see the cells; physical switches to wake the BMS when the machine needs them.
- Connectors and wiring. XT60/XT90, Anderson or the machine's original connector, silicone wire sized for the peak current.
- Enclosure. Heat-shrink and fibreglass for drone packs where weight matters; rigid cases with an IP rating for ground robots.
Robot battery compatibility: controllers, CAN and RS485
A robot controller that knows the battery's real state of charge, current limits and temperature can slow the machine down or send it to the charger before the BMS has to cut power. Before we quote we ask for the controller model and its battery protocol. Where the controller speaks CAN or RS485, we fit a BMS with that interface and agree the messages it should send; where it does not, a simple voltage and current reading still works. For drones, the flight controller usually reads voltage and current through its power module; a smart BMS can add per-cell data over UART or Bluetooth for the ground crew.
How to size a drone battery: a worked example
A cargo multirotor hovers at about 2.2 kW with its payload, and the operator wants 25 minutes of flight with 20% of the capacity left as a landing reserve.
with a 20% reserve: 0.92 ÷ 0.8 ≈ 1.15 kWh in the pack
12S Li-ion: 12 × 3.7 V = 44.4 V → 1,150 Wh ÷ 44.4 V ≈ 26 Ah
hover current: 2,200 W ÷ 44.4 V ≈ 50 A; climb and gusts ≈ 2× → about 100 A peak; near the end of the flight the voltage is lower, so allow 10–15% more current
With 5 Ah high-drain 21700 cells, six in parallel give 30 Ah and share the peak at about 17 A per cell — inside most high-drain cells' continuous rating. The pack would be 12S6P, 72 cells; then we check the weight against the drone's maximum take-off mass, because every extra cell carries itself as well as the payload.
Robot and AGV battery sizing
For ground robots the question is the shift, not the flight. A 48 V platform drawing an average of 800 W for 6 hours needs 4.8 kWh; at 90% usable depth of discharge that is about 5.3 kWh installed, or a 48 V 105 Ah LiFePO₄ pack (5.04 kWh nominal) if the robot can top up at lunch. Our forklift and AGV battery page covers warehouse fleets in more detail.
Drone battery price in the UAE: what drives the cost
- Energy and current. Cost scales with watt-hours, and high-drain cells cost more than high-energy cells of the same capacity.
- Weight targets. A pack built to the last gram — thin enclosures, exact wiring — takes more design and assembly time.
- BMS and communication. A plain protection board is cheaper than a smart BMS with CAN, RS485 and active balancing.
- One-off or series. The first pack carries the design work; repeat packs to the same drawing cost less.
Send us the brief and we return a costed proposal — request a quote.
Drone and robot batteries across the UAE, Saudi Arabia, Qatar, Kuwait, Bahrain and Oman
We build in Dubai and deliver to all seven Emirates and to Saudi Arabia, Qatar, Kuwait, Bahrain and Oman as Class 9 dangerous goods (see our delivery policy), or you collect from our workshop in Dubai Production City. Drone rules are set by each country's aviation authority; in the UAE, the GCAA requires recreational drones and their users to be registered before flying, and drones over 5 kg may fly only at approved clubs. In January 2025 the GCAA reopened recreational flying to citizens and residents with a permit, with Dubai's own framework set by its Civil Aviation Authority (The National). Commercial operators hold their own permits; we build the battery to the machine they are approved to fly.
Safety, standards and transport
Every pack leaves the workshop after a load test, labelled with its voltage, capacity and energy. The cells we use have passed the UN 38.3 transport tests that IATA requires for lithium batteries in air transport (IATA lithium batteries). The finished pack is shipped as Class 9 dangerous goods under the rules that apply to its size and production run. For ground robots and AGVs, IEC 62619 — the safety standard for lithium batteries in industrial applications, which lists AGVs among its motive uses — is the reference we design to; for small portable packs, IEC 62133-2. If you fly with spare packs, IATA allows spare lithium-ion batteries up to 100 Wh in carry-on baggage, 100–160 Wh with the airline's approval (two at most), and anything above 160 Wh only as cargo (IATA passenger guidance) — most industrial drone packs are well above that and travel as cargo. If your project needs specific test reports for a tender, tell us at the brief stage.
Related applications
The same skills run through our other work: small packs for RC cars and FPV drones, battery packs for eVTOL and aviation, traction packs for forklifts and AGVs, and battery repair and replacement for packs that are no longer made. For energy density trends that will reach drones next, see our article on semi-solid-state batteries.
From our work
- 48 V 105 Ah traction battery for a tracked robotic platform: LiFePO₄ with grade-A cells in compression holders, active balancing, a smart BMS with external temperature sensors, a communication module to the controller over RS485 and CAN with configurable commands, and physical buttons to wake the BMS and the balancer — read the full project.
- 48 V 105 Ah packs for robotic platforms in a series: EVE grade-A LiFePO₄ cells, 5.04 kWh each, 340 × 275 × 220 mm and about 37 kg, with a smart Bluetooth BMS, active balancing, temperature sensors and additional control units.
- 48 V 28 Ah power pack for a cargo drone: high-current EVE Li-ion cells in plastic holders, because the pack can reach 60 °C in operation; up to 90 A continuous, limited in the smart BMS software. That is about 1.3 kWh and over 4 kW of continuous power from one pack.
What to send us for a quote
- The machine — drone, UAV, robot or AGV — and its motors or controller model.
- The current battery: a photo of its label, its dimensions, weight and connector.
- The flight time or shift you need, the hover or average power if you know it, and the peak current.
- Where it works: indoor or outdoor, the country and city, and how it is charged and stored.
- How many packs: one prototype, spares, or a series.
Send it by WhatsApp or through the quote form — we reply on WhatsApp during working hours with questions or a costed proposal.
Frequently asked questions
Do you sell DJI batteries?
No. Consumer DJI smart batteries are made for one model and its firmware, so buy them genuine from an authorised dealer. We build new packs and repacks for industrial, agricultural, cargo and custom-frame drones that use standard Li-ion packs, and Li-ion replacements for LiPo where the current allows.
Can you make a drone battery with more flight time?
Often, yes. Newer high-capacity cells can put more energy into the same space and weight. We size the pack from the drone's hover power and maximum take-off mass, because every extra cell also has to be lifted.
What is a 3S LiPo battery?
Three lithium-polymer cells in series: 11.1 V nominal and 12.6 V fully charged. 6S is 22.2 V, 12S is 44.4 V. The capacity in mAh or Ah and the C rating give the energy and the maximum current.
LiPo or Li-ion for an industrial drone?
For long flights we usually recommend high-drain 21700 Li-ion: more energy per kilogram and a longer life. LiPo is better for short flights with very high bursts of power, such as racing and FPV.
Can you build a robot battery that talks to my controller?
Yes. We fit a BMS with CAN or RS485 and agree with you the data and commands it sends, such as state of charge, current limits, temperatures and faults. Send us the controller model and its protocol.
Can you repack my old drone or robot battery?
Usually, if it is a standard pack and not a sealed smart battery with proprietary firmware. We replace all cells with new matched ones, refit or replace the BMS, and test the pack before return.
How long does a custom drone or robot battery take?
Simple packs are built and tested from two working days; larger or more complex packs take longer, and the date is stated in the quote.
How much does a drone battery cost in the UAE?
It depends on the energy in watt-hours, the current the cells must deliver, the BMS and the enclosure, and whether it is a one-off or a series. Send us the brief and Thunderbolt returns a costed proposal.
Do you deliver drone batteries to Saudi Arabia and the rest of the GCC?
Yes. We deliver across all seven Emirates and ship to Saudi Arabia, Qatar, Kuwait, Bahrain and Oman as Class 9 dangerous goods; the method and date are in the quote.
Sources
- General Civil Aviation Authority (UAE) — UAS registration — recreational drones and users must be registered before flying; drones over 5 kg only at approved flying clubs
- The National, 9 January 2025 — GCAA reopens recreational drone use to citizens and residents with a permit; Dubai framework set by its Civil Aviation Authority
- IATA — Lithium batteries — IATA guidance and regulations for shipping lithium batteries by air
- IATA — Passengers travelling with lithium batteries — 100 Wh and 160 Wh limits for spare batteries; batteries must meet UN 38.3
- IEC 62619:2022 — safety requirements for lithium cells and batteries in industrial applications, including AGVs
- IEC 62133-2:2017 — safety requirements for portable sealed lithium cells and batteries
- Battery University — BU-410: Charging at High and Low Temperatures — Li-ion charge range 0–45 °C; heat shortens life
- Battery University — BU-808: How to Prolong Lithium-based Batteries — capacity retained after storage at 40 °C at 40% and 100% charge


