A team building a remotely controlled tracked robotic platform asked us for its traction battery. We built a 48 V 105 Ah LiFePO₄ pack — 5,040 Wh in a 340 × 275 × 220 mm body of about 37 kg — with a smart BMS that talks to the robot's controller over RS485 and CAN, a separate active balancer, external temperature sensors and physical buttons that switch the electronics on. We then built further batteries of the same type for robotic platforms, with extra control units. Every figure here comes from our own build records and photos.
The task: a traction battery that the robot can talk to
A tracked platform is hard on a battery. The tracks draw a high current when the machine turns on the spot, climbs or pushes through soft ground, and the pack rides on a chassis that shakes over every obstacle. The battery also cannot be a silent box: the platform's controller has to know the state of charge, the temperature and the current limits, so it can slow the robot down or bring it home before the battery cuts out. The customer wanted a 48 V pack of about 5 kWh, built to their own specification rather than taken from a catalogue.
What we delivered
- A 48 V 105 Ah LiFePO₄ traction battery on new EVE grade-A prismatic cells.
- Compression holders that keep the cells under even pressure in a rigid block.
- A JK (Jikong) smart BMS with Bluetooth, and a separate Heltec active balancer.
- External temperature sensors spread over the cell block.
- A battery-to-controller communication module for RS485 and CAN, with configurable commands.
- Physical buttons to start the BMS and the active balancer.
After the first battery we built more of the same 48 V 5 kWh type for robotic platforms, in special configurations with additional control units.
The battery at a glance
| Parameter | Value |
|---|---|
| Chemistry | LiFePO₄ (lithium iron phosphate) |
| Nominal voltage | 48 V (label: working range 40.0–58.4 V) |
| Capacity | 105 Ah |
| Energy | 5,040 Wh on the label (48 V × 105 Ah); about 5.4 kWh at the cells' 51.2 V nominal |
| Maximum discharge / charge current | 105 A / 50 A (from the pack label) |
| Dimensions (L × W × H) | 340 × 275 × 220 mm |
| Weight | about 37 kg |
| Cells | EVE, grade A, prismatic, in compression holders |
| BMS | JK smart BMS with Bluetooth, external temperature sensors |
| Balancing | Heltec active balancer, started by its own button |
| Communication | RS485 and CAN to the platform controller, configurable commands |
The cell block: sixteen cells under compression
The label's maximum of 58.4 V is sixteen LiFePO₄ cells at 3.65 V each, so the pack is sixteen 105 Ah prismatic cells in series. In the photos of the open pack they stand in two rows of eight, each cell in a black plastic holder, joined by bolted aluminium busbars. The holders lock into each other and make one rigid block. That matters twice on a tracked robot: the block does not shift when the chassis bangs over an obstacle, and the cells sit under even compression, which is how prismatic LiFePO₄ cells are meant to be mounted.
The balance leads run from each cell along the rows, bundled and tied down along the way so that nothing can chafe on a sharp edge under vibration. The main power leads are heavy silicone cable rated for 200 °C.
Why the balancer is a separate board
The BMS protects the pack: it cuts off on over-voltage, under-voltage, over-current and temperature. Balancing is a different job. Most BMS boards balance with a small current, while a traction pack that is used hard and recharged quickly can drift faster than that current can correct. So we fitted a dedicated active balancer: a Heltec board with its bank of capacitors mounted on the side of the cell block, which moves energy from the higher cells to the lower ones instead of burning it off as heat. On a 105 Ah pack this keeps the cells together, so the BMS does not cut the robot off early because one cell reached its limit before the others.
The smart BMS and the link to the robot's controller
The BMS is a JK (Jikong) smart board. The photos show it mounted on the opposite side of the block, with all sixteen balance leads coming into its connector and an RS485 converter module next to it. Through the communication module the platform's controller reaches the battery over RS485 or CAN, and the commands the battery answers can be configured to match the controller. CAN is the bus most vehicle and machine controllers already use, which is why we offer both. Bluetooth stays available for the engineer with a phone at the test site.
External temperature sensors are placed on the cells themselves rather than on the board, so the BMS and the controller see the temperature of the cell block, not of the electronics.
Buttons that switch the electronics on
The pack has two physical push-buttons with illuminated rings: one starts the BMS, the other starts the active balancer. When a robot sits in storage or travels to a site, the electronics can be off and draw almost nothing from the cells. Before work the operator presses the buttons, and the battery comes up and starts talking to the controller. On a robot that may stand for weeks between missions, this is the difference between a battery that is ready and one that has slowly run itself down.
The enclosure
The finished block is wrapped in a blue heat-shrink case, with yellow insulating sheets on the ends. The power leads, the communication cable and the buttons come out through the end windows, so the pack slides into the robot's battery bay and connects without opening anything. On the label we print the chemistry, the nominal voltage, the capacity, the working voltage range, the maximum currents, the energy and the production date.
Results
The pack stores 5,040 Wh in 340 × 275 × 220 mm and about 37 kg: around 136 Wh per kilogram and 245 Wh per litre of box volume (our arithmetic from the stated dimensions and weight). At its maximum discharge of 105 A, 48 V gives the platform about 5 kW of power. Like every pack we ship, it was charged, balanced and load-tested before it left the workshop. The same design then became a type: we built further 48 V 5 kWh batteries for robotic platforms, two of them in one batch on the test bench, in configurations with additional control units.
What it means for a robotics project in the UAE or the GCC
Inspection, security, agricultural and solar-panel-cleaning robots in the Gulf face the same demands as this platform, plus heat and dust. LiFePO₄ is thermally and chemically more stable than the common NMC and NCA chemistries, which is why we use it for robots that work outdoors, and the temperature sensors on the cells let the controller reduce the load when the pack is hot. A battery for a mobile machine is a pack for industrial use, the field of IEC 62619, and before it ships as Class 9 dangerous goods its design has to pass the UN 38.3 transport tests. See drone and robot battery packs in the UAE & GCC for how we build these, forklift and AGV batteries for warehouse machines, our 20 kW UPS project for the same 48 V 105 Ah format in stationary use, and our delivery terms across the GCC. To start your own, send us your brief.
Frequently asked questions
What battery does a 48 V robot need?
Start from the motors' peak and average current and the hours of work per charge. This platform uses 48 V 105 Ah LiFePO₄: 5,040 Wh, up to 105 A of discharge, about 5 kW. A robot drawing an average of 1.5 kW would run for roughly three hours on it.
Why LiFePO₄ and not Li-ion NMC for a robot?
LiFePO₄ is more thermally stable and lasts many more cycles, which suits a working machine charged every day and used outdoors. NMC is lighter for the same energy, so we use it where every kilogram counts, such as drones.
Can the battery talk to my robot's controller?
Yes. This pack has a communication module for RS485 and CAN with configurable commands, so the controller reads the state of charge, temperature and limits. Send us your controller's protocol and we set it up before delivery.
Why fit a separate active balancer if the BMS can balance?
Most BMS boards balance with a small current. A traction pack that is cycled hard can drift faster than that. A dedicated active balancer moves energy between cells continuously and keeps the whole pack usable.
How heavy is a 48 V 105 Ah LiFePO₄ battery?
This one weighs about 37 kg in a 340 × 275 × 220 mm body, around 136 Wh per kilogram. Other cell formats and enclosures change both figures; we size the box to your battery bay.
Do you build robot batteries for customers in the UAE and the GCC?
Yes. We build and test batteries in Dubai and deliver across the UAE, Saudi Arabia, Qatar, Kuwait, Bahrain and Oman; builds start from 2 working days, larger ones take longer, and the date is in the quote.
Sources
- IEC 62619:2022 — Safety requirements for secondary lithium cells and batteries for use in industrial applications — covers stationary and motive industrial uses, including AGVs
- Intertek — UN 38.3 testing — the T1–T8 transport tests lithium batteries must pass
- CAN in Automation (CiA) — CAN knowledge — the CAN bus and its ISO 11898 standardisation
- Lithium iron phosphate battery — Wikipedia — LiFePO₄ thermal and chemical stability, 3.2 V nominal cell voltage


