Thunderbolt builds 12 V and 24 V LiFePO₄ batteries in our Dubai workshop for the equipment that must never go dark: CCTV and recorders, alarm and fire panels, access control, gate and barrier motors, telecom and network cabinets, and industrial controls. We size each battery to the load and the backup time, replace 12V 7Ah to 12V 100Ah lead-acid blocks with lithium that tolerates the heat far better, capacity-test every one, and deliver across the UAE, Saudi Arabia, Qatar, Kuwait, Bahrain and Oman.
What our 12 V and 24 V battery service includes
Most security and control equipment in the region runs on small sealed lead-acid batteries — a 12V 7Ah in the alarm panel, a pair in the gate motor, a 12V 100Ah in the CCTV cabinet. In a hot cabinet they lose capacity within a couple of summers, and nobody finds out until the power fails. We build lithium batteries made for that job. You get:
- Engineering. Sizing from your equipment's current draw and the backup time you need, the choice of 12 V or 24 V, cells, BMS and case, and a costed proposal.
- The battery. New grade-A LiFePO₄ cells, matched before assembly, a BMS with protection for every cell and balancing, in a sealed case with the terminals your equipment uses.
- Options for the site. A display or battery monitor with the charge in percent and the remaining time, Bluetooth monitoring by phone, USB or 12 V outlets, a built-in solar charge controller, a second DC output at 12 V or 24 V.
- A capacity test and its log. Every battery is charged, balanced and discharged in our workshop before it leaves, so you know its real capacity.
- Delivery and service. Pickup in Dubai or delivery across the UAE and the GCC under our delivery policy; warranty up to 36 months on components and workmanship, stated in the order.
Who it is for
| Customer | What they need | Typical battery |
|---|---|---|
| CCTV and security installers | Recorders and cameras that keep recording through an outage, in hot outdoor cabinets | 12–24 V, 50–210 Ah |
| Alarm, fire and access-control contractors | Panel batteries that last longer in heat — where the system's approval allows a lithium battery | 12 V, 7–20 Ah |
| Gate and barrier companies | Backup that opens the gate in a power cut, in direct sun | 12–24 V, 7–40 Ah |
| Telecom, network and monitoring sites | Unattended DC power for routers, radios and sensors, often with a solar panel | 12–24 V, 50–210 Ah |
| Factories and workshops | Power for control cabinets, PLCs, extraction and auxiliary equipment | 12–24 V, 100–330 Ah |
| Facility managers | Replace a whole building's lead-acid stock with batteries that last | 12 V, 7–100 Ah, by the batch |
Why replace 12 V lead-acid with LiFePO₄
- Heat. Sealed lead-acid life halves with every 8 °C rise; a battery rated for 10 years at 25 °C gets about 30 months at a constant 41 °C, according to Battery University. Outdoor cabinets in the Gulf summer are hotter than that.
- Same voltage. Four LiFePO₄ cells in series give 12.8 V, close to six 2 V lead-acid cells (Battery University), so the equipment sees the battery it expects.
- About twice the usable energy. You can use 80–90% of a LiFePO₄ battery; lead-acid lasts longest when used to about half. A 12V 100Ah LiFePO₄ does roughly the work of a 12V 170–200Ah lead-acid.
- Lighter and smaller. Easier to lift into a pole cabinet or a ceiling void.
- You can see it. A display or a Bluetooth BMS shows the real charge and health; a lead-acid block shows nothing until it fails.
How it works: from brief to a working battery
- Brief. You send the equipment, its current draw or power supply rating, the backup time, the battery you are replacing and a photo of the cabinet — by WhatsApp or the quote form.
- Engineering and proposal. The battery configuration, the cells, the case size, the charger check, the warranty, the price and the date.
- Assembly. Cell matching, assembly and BMS setup in our Dubai workshop.
- Capacity test. Each battery is charged, balanced and discharged; you receive the measured capacity.
- Delivery or pickup. Builds start from two working days; batches and larger batteries take longer and the date is in the quote.
- Support. Questions answered from the BMS data; service and capacity tests when needed.
Why Thunderbolt
- Built here, not imported. We assemble and test in Dubai, so the battery is made for your cabinet and we can service it locally.
- Custom to the cabinet. Odd sizes, side terminals, a second output voltage, a solar controller inside the case.
- Measured, not promised. Our 12V 105Ah batteries on grade-A cells have measured about 112 Ah on test.
- One batch, one standard. For a building or a fleet of sites we build identical batteries, numbered and logged.
12 V and 24 V LiFePO₄ batteries we build
| Battery | Voltage | Capacity | Typical use |
|---|---|---|---|
| 12V 7Ah class | 12.8 V | 7–20 Ah | Alarm and fire panels, access control, small gate motors |
| 12V 50Ah | 12.8 V | 50–60 Ah | Small CCTV systems, routers, lead-acid replacement in equipment |
| 12V 100Ah | 12.8 V | 100–105 Ah | CCTV recorders and cameras, telecom cabinets, solar-charged sites |
| 12V 200Ah and up | 12.8 V | 200–330 Ah | Long backup, industrial auxiliaries, inverters |
| 24V battery | 25.6 V | 50–210 Ah | Gate and barrier motors, 24 V controls, larger CCTV systems |
These are the sizes we quote most often. Anything in between, or a 36 V or 48 V battery for a larger system, is a normal custom build.
12V 100Ah LiFePO₄ battery: what to look for
The "LiFePO₄ battery 12V 100Ah" is the most searched lithium size in the region, and the market is full of them. What separates one that lasts from one that does not is mostly hidden inside the case:
- The cells. Grade-A prismatic cells of the current year's production from an established maker. We build on EVE 105 Ah cells, so our "100Ah" battery is 105 Ah on the label and measures above it.
- The BMS current. The BMS sets the real limit. Our 12V 105Ah "Pro" version delivers 100 A continuous and loads up to 1,200 W; a CCTV cabinet needs far less, an inverter or a winch far more.
- Balancing. Built-in balancing, or an active balancer of up to 5 A that keeps the cells together over years of standby.
- Joints. Torque-checked busbars on thread-locker, or laser-welded connections between the cells on our newer builds.
- A real test. Ask for the measured capacity, not just the label.
12V 7Ah battery replacement for alarm panels and gates
The 12V 7Ah sealed lead-acid block is in nearly every alarm panel, access-control power supply and many gate motors. A lithium version in the same size is a good upgrade — with three checks first:
- The charger. Panel chargers hold the battery at a fixed float voltage chosen for lead-acid. A LiFePO₄ battery usually works on it, but may charge slowly and not quite to full; we set the BMS so the battery works safely on your panel's charger and tell you what charge level to expect.
- The low-battery cut-off. The panel's low-battery warning is set for lead-acid; a lithium battery's voltage stays flat and then drops quickly at the end. On lithium the warning comes late, close to empty, so we size the battery to cover the full backup time before that point and tell you what warning time to expect.
- The rules for the system. Intruder alarm power supplies are covered by EN 50131-6 and fire alarm power supplies by EN 54-4. Where a system has to be approved — by Dubai's SIRA for security systems, or by civil defence for fire systems — confirm with your consultant which battery type and backup time the approval expects before changing chemistry.
CCTV battery backup: how to size it
A site has four IP cameras at about 6 W each and a recorder at 15 W, all on 12 V, and the owner wants 24 hours of recording without mains power.
40 W × 24 h = 960 Wh
÷ 0.9 usable depth of discharge ≈ 1,070 Wh installed
12.8 V × 105 Ah = 1,344 Wh → one 12V 105Ah LiFePO₄ battery
the same backup on lead-acid at 50% depth: 960 ÷ 0.5 = 1,920 Wh → about 12V 160Ah
Two more checks: the power supply or charger must refill the battery before the next outage, and the cabinet temperature decides how much margin to add. If there is no mains at all, a solar panel and a charge controller inside the battery case turn the same battery into a stand-alone power source.
Industrial battery for controls, telecom and remote sites
"Industrial battery" covers everything from a control cabinet's backup to a remote monitoring post. What our industrial 12 V and 24 V builds have in common: a sealed, serviceable case; a BMS that protects the cells against over-discharge, over-current and temperature; Bluetooth monitoring where nobody can open the case often; and, when needed, two DC outputs, an AC outlet, or a charge controller for solar or wind. For 48 V telecom backup and larger systems, see our page on UPS and inverter battery backup.
12 V batteries for Gulf heat, dust and humidity
- Placement. A shaded cabinet with ventilation, or the battery in the cooler lower part of the cabinet, adds years. We ask for photos of the cabinet before we quote.
- BMS temperature limits. The BMS stops charging when the cells are too hot and stops discharging if they overheat.
- Sealed cases. Waterproof, serviceable cases for outdoor and coastal sites, with insulated terminals and covers on outdoor modules.
- Dust. Sealed connectors and cases keep fine sand away from the terminals and the BMS.
12V battery price in the UAE: what drives the cost
- Capacity. Cost scales with ampere-hours; a 12V 100Ah costs far more than a 12V 7Ah, but replaces a 200 Ah lead-acid bank.
- Cells and BMS. Grade-A cells and a BMS with a higher current and Bluetooth cost more than a basic board.
- Options. A display, USB outlets, a solar controller or a second output voltage add parts and assembly time.
- Quantity. A batch of identical batteries for a building or a set of sites is quoted as a batch.
- Lifetime cost. A LiFePO₄ battery costs more to buy than lead-acid; in a hot cabinet the lead-acid block is replaced several times over the same years.
Send us the brief and we return a costed proposal — request a quote.
12 V and 24 V batteries across the UAE and the GCC
We build in Dubai and deliver to all seven Emirates and to Saudi Arabia, Qatar, Kuwait, Bahrain and Oman (see our delivery policy). Small batteries ship by courier as Class 9 dangerous goods; batches go by road. The battery is the same everywhere; the site changes it: coastal compounds in the UAE, Qatar, Bahrain and Kuwait need more attention to humid, salty air, and remote farms, pumping stations and road sites in Saudi Arabia and Oman more often need solar charging and longer autonomy.
Safety, standards and paperwork
Every battery leaves the workshop after a capacity test and is shipped at a reduced charge. The cells we use have passed the UN 38.3 transport tests. The finished pack is shipped as Class 9 dangerous goods under the rules that apply to its size and production run. For industrial and stationary uses we design to IEC 62619, the safety standard for lithium cells and batteries in industrial applications. The alarm and fire standards above apply to the power supply as a whole; if your project needs specific certificates for an approval or a tender, tell us at the brief stage.
Related applications
The same 12 V and 24 V batteries power boats and yachts, caravans and motorhomes and 24 V bus and truck systems. Larger backup is covered by UPS and inverter batteries and solar battery storage; battery boxes with sockets by our portable power stations.
From our work
- Two 12V 105Ah LiFePO₄ batteries with battery monitors: EVE 105 Ah prismatic cells and a Daly BMS, with a built-in monitor showing the charge in percent, the remaining Ah, the remaining time at the current load, voltage, current and power. On test both delivered about 112 Ah each, above the 105 Ah rating.
- 12V 105Ah with a solar charge controller: a controller built into our standard battery, a solar panel matched to it, charging checked through the smart BMS app, and the outdoor module protected by a rubber cover so the system runs in the open around the clock.
- 24V 105Ah power station for an outdoor site: a 24 V LiFePO₄ battery with Bluetooth in a sealed, serviceable case, camouflaged for outdoor placement, with 24 V DC and AC outputs up to 2,000 W, a charge indicator and a short-circuit breaker; it charges from empty to full in as little as two hours.
- 24V 105Ah with solar and wind charging: 2.7 kWh in a waterproof case with the charging electronics for solar panels and a wind turbine inside, and separate 12 V and 24 V DC outputs; state of charge by Bluetooth on iOS, Android or desktop.
- 12V 105Ah for a workshop machine: a battery with its own distribution enclosure, built to power the extraction system of a CNC machine.
- 12V 330Ah high-current battery: built with a smart BMS and tested under a simulated real load of 60 A before delivery.
- Lead-acid replaced: a 12V 50Ah Li-ion NMC battery in place of a 12 V 12 Ah lead-acid block that had lost almost all its capacity — about four times the running time the old battery gave even when new.
- 12V 105Ah with laser-welded cells: our first 12 V battery with the cells joined in series by laser welding instead of bolted busbars.
What to send us for a quote
- The equipment — cameras and recorder, panel, gate motor, controller — and its current draw or power supply rating.
- The battery you are replacing (for example 12V 7Ah or 12V 100Ah), with a photo of its label and the cabinet.
- The backup time you need, and whether there is mains, solar or nothing at all.
- The number of batteries and the country and city of the sites.
Send it by WhatsApp or through the quote form — we reply on WhatsApp during working hours with questions or a costed proposal.
Frequently asked questions
Can a LiFePO₄ battery replace a 12V lead-acid battery directly?
In most equipment, yes: four LiFePO₄ cells give 12.8 V, close to a 12 V lead-acid block. Check the charger first — it must not exceed the lithium battery's limits — and the low-battery threshold of the equipment.
How long does a 12V 100Ah battery last on CCTV?
Divide the usable energy by the load. A 12V 105Ah LiFePO₄ battery holds about 1,340 Wh; with 90% usable, it runs a 40 W camera system for about 30 hours.
Is a 12V 100Ah LiFePO₄ battery worth it compared with lead-acid?
In Gulf heat, usually yes. You can use 80–90% of it instead of about half, it lasts thousands of cycles, and it tolerates a hot cabinet far better than lead-acid, though it also ages faster when hot and will not charge above its temperature limit.
Can I use a lithium 12V 7Ah battery in my alarm panel?
Often, but check the panel's charger voltage, its low-battery warning and whether the system's approval specifies a battery type. Where an approval or a standard such as EN 50131-6 or EN 54-4 applies, confirm with your consultant first.
Do you make 24V batteries for gate motors and barriers?
Yes. We build 24 V LiFePO₄ batteries sized to the motor's current and the number of openings you need in an outage, in sealed cases for outdoor cabinets.
Can the battery charge from a solar panel?
Yes. We build the charge controller into the battery case and match a panel to it, so a camera, a router or a sensor can run where there is no mains at all.
What is an industrial battery?
A battery built for equipment rather than vehicles or consumer devices: control cabinets, telecom and monitoring sites, backup for machines. We build them as 12 V and 24 V LiFePO₄ batteries with a protective BMS, sealed cases and monitoring.
How much does a 12V lithium battery cost in the UAE?
It depends mostly on the capacity, the BMS and the options such as a display, outlets or a solar controller, and on how many you order. Send us the brief and Thunderbolt returns a costed proposal.
Sources
- Battery University — BU-806a: How Heat and Loading affect Battery Life — sealed lead-acid life halves with every 8 °C rise; 10 years at 25 °C, about 30 months at a constant 41 °C
- Battery University — BU-205: Types of Lithium-ion — four LiFePO₄ cells in series give 12.80 V, similar to six 2 V lead-acid cells; cycle life and thermal stability
- BSI — BS EN 50131-6:2017+A1:2021 — alarm systems, intrusion and hold-up systems: power supplies
- BSI — BS EN 54-4 — fire detection and fire alarm systems: power supply equipment
- Security Industry Regulatory Agency (SIRA), Dubai — Dubai's regulator for security systems, services and system providers
- IEC 62619 — safety requirements for lithium cells and batteries in industrial applications, including telecom and UPS
- Intertek — UN 38.3 testing — nearly all lithium batteries must pass section 38.3 of the UN Manual of Tests and Criteria for transport


