A research organisation preparing an expedition needed batteries for its underwater tugs — the hand-held scooters that pull a diver through the water. We designed and modelled two 36 V 12 Ah LiFePO₄ batteries, 3D-printed their holders ourselves, assembled them on the best components we could source and supplied a fast charger with each, so the team received them ready to use. This page sticks to what we built and what our photos show; where it talks about underwater packs in general, it says so.
The task
The customer had underwater tugs for an expedition and needed two batteries for them, plus a way to recharge them quickly between dives. A scooter's battery space is set by its hull, so the pack could not be a box picked from a shelf: it had to be designed around the space it goes into, at the voltage the motor expects.
What we delivered
- Two LiFePO₄ batteries, 36 V 12 Ah each, designed and modelled by us.
- Holders 3D-printed in our workshop (FDM) for this pack.
- Two fast chargers, one for each battery.
- Assembly to a ready-to-use state: wired, wrapped and handed over with nothing left to do.
The batteries at a glance
| Parameter | Value |
|---|---|
| Quantity | 2 batteries + 2 fast chargers |
| Chemistry | LiFePO₄ (lithium iron phosphate) |
| Voltage / capacity | 36 V / 12 Ah per battery |
| Energy | about 432 Wh per battery (36 V × 12 Ah) |
| Power class | 450 W |
| Cells | cylindrical LiFePO₄, marked 32700, 6,000 mAh, 3.2 V |
| Holders | our design, FDM 3D-printed |
| Shape | round: cells in a ring, in two tiers |
How it was built
A round pack. We modelled each battery as a cylinder: the cells stand in a ring around a central channel, in two tiers one above the other. The photos of the end plates show the pattern — cell ends in a circle, and a hole in the middle. A round pack fills a round space with no dead corners, and the central channel gives the wires a path from one end to the other.
The cells. The cells are cylindrical LiFePO₄ marked 32700, 6,000 mAh, 3.2 V. With 6 Ah cells, a 12 Ah battery means two cells in parallel in every series group.
Printed holders. Each tier sits between grey FDM-printed rings that hold every cell in its place, and the tiers are tied together into one stack. Yellow fibreglass discs insulate the tiers from each other and close the top. This is the part we could not buy: the holders exist only because we drew them for this hull and printed them in our own workshop.
The BMS and wiring. A compact BMS sits on the top disc, with its balance connector and a temperature-sensor (NTC) lead going down into the cells. The power leads are 12 AWG silicone cable rated for 200 °C, and they leave the pack through the hole in the centre of the top disc.
The finish. The stack is wrapped tight in blue heat-shrink, with the leads coming out at the top. Each battery went out with its own fast charger.
Results
The team received two complete sets — battery and fast charger — ready to fit and use, with nothing left to assemble or adjust. At a full 450 W a 432 Wh battery runs for roughly an hour (our arithmetic, before losses); at part throttle, which is how scooters spend most of a dive, it lasts longer. With two batteries and two chargers, one set can charge on deck while the other is in the water.
How underwater packs are designed — general practice
The source for this project is short, so here is how we approach packs of this kind in general. These points describe the engineering of underwater batteries, not statements about this particular order.
- Sealing belongs to a housing. In most scooters the battery sits inside a sealed hull or canister; the pack itself is protected against handling, not against water. If the pack must survive water on its own, its enclosure is specified by the IEC 60529 IP code, where IPX7 means temporary immersion to 1 m and IPX8 continuous immersion under conditions the maker states. Neither rating means "fit for diving depth" — depth is a matter of the hull.
- Buoyancy and trim. A scooter is trimmed to be close to neutral in the water. The battery is one of its heaviest parts, so its mass and where it sits in the hull matter to the designer of the vehicle; we give the exact weight and centre of the pack when asked.
- Condensation and salt. A hull opened in humid air and closed again traps moisture, and salt water attacks connectors. Short leads and connections sealed under heat-shrink help, and so does charging the battery dry and out of the water.
- Chemistry. LiFePO₄ is more thermally and chemically stable than the common NMC and NCA types, which counts in a closed hull a diver holds at arm's length.
What it means for marine projects in the UAE and the GCC
Dive centres, marine research teams, survey crews and film units along the Gulf and the Gulf of Oman use scooters, small ROVs and instruments with exactly this kind of battery space: round, tight and set by the hull. We design the pack to the space, print the holders, and add the charger. Lithium batteries travel as Class 9 dangerous goods, and every design has to pass the UN 38.3 transport tests; see our delivery terms. For boats, house banks and starter batteries see marine and boat lithium batteries in the UAE & GCC; for small underwater robots, drone and robot battery packs. Send us the hull drawing and the motor's figures.
Frequently asked questions
What battery does an underwater scooter use?
Most use a lithium pack inside the sealed hull, sized to the motor's voltage and the space available. This project used 36 V 12 Ah LiFePO₄ — about 432 Wh — built round to fill a round space.
Can you build a battery to fit my scooter's hull?
Yes. We model the pack from the inner dimensions of the hull and print the cell holders ourselves, so the battery fits the space instead of the other way round.
How long does a 36 V 12 Ah scooter battery last?
About an hour at a full 450 W, by simple arithmetic before losses, and longer at part throttle. The real figure depends on the motor, the speed and the water.
Is the battery itself waterproof?
In most scooters the hull provides the seal and the pack inside it is protected against handling, not against water. If the pack must be waterproof on its own, it needs an enclosure rated under the IEC 60529 IP code — tell us at the quote stage.
Why LiFePO₄ for an underwater battery?
It is more thermally and chemically stable than the common NMC and NCA types, lasts many cycles, and is a safer choice in a closed hull carried by a diver.
Do you build marine batteries in the UAE and the GCC?
Yes. We build and test batteries in Dubai and deliver across the UAE, Saudi Arabia, Qatar, Kuwait, Bahrain and Oman; builds start from 2 working days, and the date is in the quote.
Sources
- IEC 60529 — Degrees of protection provided by enclosures (IP Code) — the standard behind IP ratings
- IP code — Wikipedia — what IPX7 (temporary immersion to 1 m) and IPX8 (continuous immersion) mean
- Intertek — UN 38.3 testing — the T1–T8 transport tests lithium batteries must pass
- Lithium iron phosphate battery — Wikipedia — LiFePO₄ thermal and chemical stability, 3.2 V nominal cell voltage


